Difference between revisions of "Interface/DPC-20/eng"
Jump to navigation
Jump to search
(Created page with "DPC-20 * HW Type = PC USB-C to 3pin(PWM/TTL) and 4pin(485/CAN) interface * You can set up and test HiTek digital servos. * Depending on the control method (PWM, 485, CAN), it...") |
|||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
DPC-20 | DPC-20 | ||
* HW Type = PC USB-C to 3pin(PWM/TTL) and 4pin(485/CAN) interface | * HW Type = PC USB-C to 3pin(PWM/TTL) and 4pin(485/CAN) interface | ||
* You can set up and test | * You can set up and test HiTEC digital servos. | ||
* Depending on the control method (PWM, 485, CAN), it can be used instead of the existing DPC-11, DPC-485, and DPC-CAN. | * Depending on the control method (PWM, 485, CAN), it can be used instead of the existing DPC-11, DPC-485, and DPC-CAN. | ||
* Since the communication content and method are different depending on the type of servo, a separate UI is used. | * Since the communication content and method are different depending on the type of servo, a separate UI is used. | ||
| Line 8: | Line 8: | ||
|- | |- | ||
| Servo Series | | Servo Series | ||
| Compatible interface | |||
| UI | | UI | ||
| UI Link | | UI Link | ||
|- | |- | ||
| 5/7 series | | 5/7 series | ||
| DPC-11 PC UI (3.1.0+) | | DPC-11, DPC-20 | ||
| [[UI/DPC-11/ | | rowspan="4" | DPC-11 PC UI (3.1.0+) | ||
| rowspan="4" | [[UI/DPC-11/eng | DPC-11 PC UI]] | |||
|- | |- | ||
| 9 series | | 9 series | ||
| DPC-11 | | DPC-11, DPC-20 | ||
|- | |- | ||
| D series | | D series | ||
| DPC-11 | | DPC-11, DPC-20 | ||
|- | |- | ||
| D-485 series | | D-485 series | ||
| DPC- | | DPC-485, DPC-20 | ||
|- | |- | ||
| CAN series | | CAN series | ||
| CAN AIO(All in One) UI (2023_06_14+) | | DPC-CAN, DPC-20 | ||
| [[UI/CAN/AIO/ | | CAN AIO (All in One) UI (2023_06_14+) | ||
| [[UI/CAN/AIO/eng | AIO UI]] | |||
|- | |- | ||
|} | |} | ||
| Line 41: | Line 35: | ||
* NOTE - DPC-485 | * NOTE - DPC-485 | ||
** For cases other than the D-485 series, a separate dedicated UI may be used. | ** For cases other than the D-485 series, a separate dedicated UI may be used. | ||
** At this time, if you use DPC-20 instead, connect it to USB | ** At this time, if you use DPC-20 instead, connect it to USB, wait about 20 seconds, then open the COM port and use it like you did with DPC-485. | ||
* NOTE - When changing UI | |||
** Please disconnect the USB cable from the DPC-20 and reconnect it. | |||
Latest revision as of 07:59, 30 May 2024
DPC-20
- HW Type = PC USB-C to 3pin(PWM/TTL) and 4pin(485/CAN) interface
- You can set up and test HiTEC digital servos.
- Depending on the control method (PWM, 485, CAN), it can be used instead of the existing DPC-11, DPC-485, and DPC-CAN.
- Since the communication content and method are different depending on the type of servo, a separate UI is used.
| Servo Series | Compatible interface | UI | UI Link |
| 5/7 series | DPC-11, DPC-20 | DPC-11 PC UI (3.1.0+) | DPC-11 PC UI |
| 9 series | DPC-11, DPC-20 | ||
| D series | DPC-11, DPC-20 | ||
| D-485 series | DPC-485, DPC-20 | ||
| CAN series | DPC-CAN, DPC-20 | CAN AIO (All in One) UI (2023_06_14+) | AIO UI |
- NOTE - DPC-485
- For cases other than the D-485 series, a separate dedicated UI may be used.
- At this time, if you use DPC-20 instead, connect it to USB, wait about 20 seconds, then open the COM port and use it like you did with DPC-485.
- NOTE - When changing UI
- Please disconnect the USB cable from the DPC-20 and reconnect it.